Ford Sierra

1982-1993 of release

Repair and operation of the car


Ford Siyerra
+ 1.2. Identification of the car
+ 2. Maintenance
- 3. General data
   + 3.1. Cars with petrol engines
   - 3.2. Cars with diesel engines
      - 3.2.1. Changes in a car design from 1988 to 1993.
         3.2.1.1. Dm3 engine 2,3
         - 3.2.1.2. Dm3 engine 1,8
            3.2.1.2.1. Technical characteristics
            3.2.1.2.2. Head of the block of cylinders
            3.2.1.2.3. Block of cylinders
            3.2.1.2.4. Krivoshipno-shatunny mechanism
            3.2.1.2.5. System of gas distribution
            3.2.1.2.6. Lubrication system
            3.2.1.2.7. Cooling system
            3.2.1.2.8. Fuel system
            3.2.1.2.9. Tightening moments
            3.2.1.2.10. Adjustment of the engine
         + 3.2.1.3. Fuel system
         + 3.2.1.4. The repair which is not demanding removal of the engine
         3.2.1.5. Removal and installation of the engine
         3.2.1.6. Dismantling of the engine
         3.2.1.7. Check of details
         3.2.1.8. Check of gaps of a bent shaft and rods
         3.2.1.9. Assembly of the engine
         3.2.1.10. Lubrication system
         3.2.1.11. Cooling system
         3.2.1.12. Coupling
         3.2.1.13. Mechanical MT 75 five-speed transmission
         3.2.1.14. Power shaft and back bridge
         3.2.1.15. System of steering
         3.2.1.16. Forward suspension bracket
         3.2.1.17. Brake system
         3.2.1.18. Electric equipment
         3.2.1.19. General data
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


a773976c



3.2.1.2.9. Tightening moments
GENERAL INFORMATION

Bolts of fastening of a head of the block of cylinders (every time new bolts):
  – 1 stage
20 – 30 Nanometers
  – 2nd stage
76 – 92 Nanometers
  – 3rd stage
to wait 2 minutes
  – 4th stage
to tighten on 90 °
Covers of bearings of a cam-shaft
16 – 22 Nanometers
Covers of radical bearings:
  – 1 stage
20 – 30 Nanometers
  – 2nd stage
to tighten on 45 °
Covers of rods:
  – 1 stage
20 – 30 Nanometers
  – 2nd stage
to tighten on 60 °
  – 3rd stage
to tighten on 20 °
Flywheel:
  – 1 stage
15 – 20 Nanometers
  – 2nd stage
to tighten on 45 °
  – 3rd stage
to tighten on 45 °
Pulley of an intermediate shaft
40 – 51 Nanometers
Pulley of the fuel pump
20 – 25 Nanometers
Tension device of a gear belt of the drive of the fuel pump
40 – 57 Nanometers
Cam-shaft pulley
  – M6 bolt
8 – 10 Nanometers
  – M8 bolt
27 – 33 Nanometers
Tension device of a gear belt of the drive of a cam-shaft
45 – 55 Nanometers
Intermediate pulley
40 – 51 Nanometers
Casing of driving belts of system of gas distribution and fuel pump
8 – 10 Nanometers
Back cover to the block of cylinders
16 – 21 Nanometers
Forward cover to the block of cylinders
20 – 28 Nanometers
The oil pump to the block of cylinders
20 – 25 Nanometers
Basic bearing of an intermediate shaft
8 – 10 Nanometers
Sealant of an intermediate shaft
20 – 25 Nanometers
Oil pallet
6 – 9 Nanometers
Fuel pump
18 – 22 Nanometers.
Cover of a head of the block of cylinders
3 – 4 Nanometers
Glow plugs
25 – 30 Nanometers
Nozzles to a head of the block of cylinders
60 – 80 Nanometers
Connections of pipelines of nozzles
15 – 25 Nanometers
Inlet and final collectors to a head of the block of cylinders
10 – 14 Nanometers
Bolts of a final collector
20 – 28 Nanometers