Ford Sierra

1982-1993 of release

Repair and operation of the car



Ford Siyerra
+ 1.2. Identification of the car
+ 2. Maintenance
- 3. General data
   + 3.1. Cars with petrol engines
   - 3.2. Cars with diesel engines
      - 3.2.1. Changes in a car design from 1988 to 1993.
         3.2.1.1. Dm3 engine 2,3
         - 3.2.1.2. Dm3 engine 1,8
            3.2.1.2.1. Technical characteristics
            3.2.1.2.2. Head of the block of cylinders
            3.2.1.2.3. Block of cylinders
            3.2.1.2.4. Krivoshipno-shatunny mechanism
            3.2.1.2.5. System of gas distribution
            3.2.1.2.6. Lubrication system
            3.2.1.2.7. Cooling system
            3.2.1.2.8. Fuel system
            3.2.1.2.9. Tightening moments
            3.2.1.2.10. Adjustment of the engine
         + 3.2.1.3. Fuel system
         + 3.2.1.4. The repair which is not demanding removal of the engine
         3.2.1.5. Removal and installation of the engine
         3.2.1.6. Dismantling of the engine
         3.2.1.7. Check of details
         3.2.1.8. Check of gaps of a bent shaft and rods
         3.2.1.9. Assembly of the engine
         3.2.1.10. Lubrication system
         3.2.1.11. Cooling system
         3.2.1.12. Coupling
         3.2.1.13. Mechanical MT 75 five-speed transmission
         3.2.1.14. Power shaft and back bridge
         3.2.1.15. System of steering
         3.2.1.16. Forward suspension bracket
         3.2.1.17. Brake system
         3.2.1.18. Electric equipment
         3.2.1.19. General data
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment





3.2.1.2.3. Block of cylinders

GENERAL INFORMATION

Block of cylinders of the engine

1 – block of cylinders of the engine,
2 – back cover,
3 – sealing ring,
4 – oil discharge stopper,
5 – laying of the oil pallet,
6 – oil pallet,

7 – cap of a technological opening of the block of cylinders,
8 – cap of the oil channel,
9 – a stopper of discharge of cooling liquid from the block of cylinders,
10 – the stopper closing an opening for installation of a bent shaft in VMT

The pig-iron block of cylinders has cylinders and nests of bearings of a bent shaft executed directly in its material. Contains five nests of radical bearings of a bent shaft. Between the next cylinders in the block of cylinders there are channels for passing of cooling liquid.

Designation of the block of cylinders: 89 FF 6015 AB.

Diameters of cylinders:
  – nominal:
     • group A
82,500 – 82,515 mm
     • group B
82,515 – 82,530 mm
     • group C
82,660 – 82,675 mm
     • group D
82,675 – 82,690 mm
  – repair:
+ 0,5
83,000 – 83,015 mm
+ 1,0
83,500 – 83,515 mm
Diameter of openings of nests of inserts of radical bearings
53,683 – 53,696 mm