Ford Sierra

1982-1993 of release

Repair and operation of the car



Ford Siyerra
+ 1.2. Identification of the car
+ 2. Maintenance
- 3. General data
   - 3.1. Cars with petrol engines
      3.1.1. Masses and transfer numbers
      3.1.2. Operational liquids
      + 3.1.3. Changes in a car design from 1984 to 1986.
      - 3.1.4. Changes in a car design from 1987 to 1989.
         3.1.4.1. OHC engine
         + 3.1.4.2. Dm3 CVH 1,8 engine
         + 3.1.4.3. DOHC engine
         - 3.1.4.4. Service and repair
            3.1.4.4.1. System of ignition
            3.1.4.4.2. System of injection
            3.1.4.4.3. Scheme of the EES IV system of the DOHC 2,0 engine of dm3
            3.1.4.4.4. Check and adjustment of the EEC IV system
            3.1.4.4.5. Elimination of malfunctions
            3.1.4.4.6. Check of elements of the EEC IV system
            3.1.4.4.7. System of gas distribution
            3.1.4.4.8. Head of the block of cylinders of the engine
            3.1.4.4.9. Dismantling of the engine
            3.1.4.4.10. Assembly of the engine
            3.1.4.4.11. Lubrication system
         + 3.1.4.5. Coupling
         3.1.4.6. Mechanical five-speed transmission of N type
         + 3.1.4.7. Mechanical MT 75 five-speed transmission
         3.1.4.8. Automatic transmission
         3.1.4.9. Forward suspension bracket
         + 3.1.4.10. Brake system
         + 3.1.4.11. Electric equipment
         3.1.4.12. General data
      + 3.1.5. Changes in a car design from 1990 to February, 1993.
   + 3.2. Cars with diesel engines
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


a773976c



3.1.4.4.5. Elimination of malfunctions

GENERAL INFORMATION

Elimination of malfunctions

Group-
pas
Code
Reason
Malfunction elimination method
1
13
Sensor of temperature of cooling liquid
  – if the following code 23 or 33, you watch group 6;
  – if temperature of cooling liquid too low then to warm up the engine and and to repeat check;
  – to check connections of wires.
2
14
24
34
The sensor of temperature of the arriving air
  – to check connections of wires;
  – to check sensor resistance (between contacts of the socket of the electronic actuation device "25" and "46"):
at 20 °C: 35 – 40 Ohms;
at 40 °C: 15 – 18 Ohms;
at 60 °C: 7 – 8,5 Ohms.
3
15
Sensor of provision of a butterfly valve
  – if the following code 25 or 35, you watch group 7;
  – to check a condition of a cable of a pedal of an accelerator;
  – to check the sensor and its wires;
  – if malfunction is still present, then to replace the electronic EEC IV actuation device.
4
17
Sensor of absolute pressure
  – if the following code 25 or 35, you watch group 7;
  – to check vacuum in an inlet collector idling – has to make 400–600 mm Hg;
  – to check tightness of an inlet collector and pressure of compression;
  – to check tightness of the vacuum pipeline, accumulator and sensor.
5
21
Wrong signal of ignition of "PIP"
  – to check connections of wires of the electronic EEC IV actuation device;
  – to check resistance between contacts of the socket of the electronic actuation device:
"56" and "36" – 2–5 kOhm;
"16" and "40" – 0–2,5 Ohms;
between (+) the accumulator and the ignition coil – 0–2,5 Ohms;
  – to replace the ignition distributor;
  – to replace the electronic EEC IV actuation device.
6
22
23
Sensor of temperature of cooling liquid
  – to check a state and connection of the socket;
  – to check sensor resistance:
at 20 °C: 35–40 Ohms;
at 40 °C: 15–18 Ohms;
at 60 °C: 7–8,5 Ohms
  – to check a plait of wires;
  – to replace the sensor;
  – to replace the electronic EEC IV actuation device.
7
25
35
43
Sensor of provision of a butterfly valve
  – to check the socket;
  – to check functioning of a butterfly valve and a cable of a pedal of an accelerator;
  – to check resistance between contacts of the socket of the electronic actuation device:
"26" and "46" – 315–550 Ohms;
"47" and "46" – 1,2–2 kOhm;
"26" and "47" – 3,5–5,5 kOhm
  – to check electric wires;
  – to replace the sensor;
  – to replace the electronic EEC IV actuation device.
8
27
37
42
Sensor of absolute pressure
  – to check the socket;
  – to check a condition of the vacuum pipeline and also whether it is original;
  – to check vacuum in an inlet collector idling – has to make 400–600 mm Hg;
  – to check electric wires;
  – to replace the sensor;
  – to replace the electronic EEC IV actuation device.
9
46
47
48
Valve of management of idling
  – to check a condition of the valve;
  – to measure valve winding resistance. Has to make 6–9 Ohms. If value wrong then to replace the valve;
  – to check electric wires.