Ford Sierra

1982-1993 of release

Repair and operation of the car



Ford Siyerra
+ 1.2. Identification of the car
+ 2. Maintenance
+ 3. General data
- 4. Engines
   - 4.1. Petrol engines
      - 4.1.1. Technical characteristics
         4.1.1.1. Head of the block of cylinders
         4.1.1.2. Block of cylinders of the engine
         4.1.1.3. Krivoshipno-shatunny mechanism
         4.1.1.4. System of gas distribution
         4.1.1.5. Lubrication system
         4.1.1.6. Cooling system
         4.1.1.7. Fuel system
         4.1.1.8. System of ignition
         4.1.1.9. Tightening moments
      4.1.2. Adjustment of gaps of valves
      + 4.1.3. System of ignition
      + 4.1.4. Fuel system
      + 4.1.5. The repair which is not demanding removal of the engine
      4.1.6. Removal and installation of the engine
      4.1.7. Dismantling of the engine
      4.1.8. Identification of the interacting parts
      4.1.9. Assembly of the engine
      4.1.10. Replacement of pistons
      4.1.11. Removal and installation of an intermediate shaft
      4.1.12. System of gas distribution
      4.1.13. Lubrication system
      + 4.1.14. Cooling system
      4.1.15. Suspension bracket of the power unit
      4.1.16. System of production of the fulfilled gases
   + 4.2. Diesel engine
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


a773976c



4.1.1.9. Tightening moments

GENERAL INFORMATION

Bolts of covers of radical bearings
88 – 102 Nanometers
Bolts of rods
40 – 47 Nanometers
Bolt of a pulley of a bent shaft
55 – 60 Nanometers
Cam-shaft gear wheel bolt
45 – 50 Nanometers
Flywheel bolts
67 – 70 Nanometers
Bolts of fastening of the oil pump
17 – 21 Nanometers
Bolts of a cover of the oil pump
9 – 13 Nanometers
Bolts of the oil pallet (a tightening order – you watch subsection 4.1.9)
  – 1st stage
1 – 2 Nanometers
  – 2nd stage
6 – 8 Nanometers
  – the 3rd stage (after 20 minutes of operation of the engine)
8 – 10 Nanometers
Stopper of discharge of oil in the oil pallet
21 – 28 Nanometers
Oil pressure sensor
12 – 15 Nanometers
Bolts of adjustment of a gap of valves about levers of valves
50 – 55 Nanometers
Bolts of a head of the block of cylinders (a tightening order – see in subsection 4.1.5.4)
  – 1st stage
40 – 45 Nanometers
  – 2nd stage
50 – 70 Nanometers;
  – the 3rd stage (10 – 20 min. later)
73 – 83 Nanometers
  – the 4th stage (after 15 minutes of operation of the engine at the speed of 1000 rpm; at the hot engine)
95 – 115 Nanometers
Casing of system of gas distribution
13 – 17 Nanometers
Inlet collector
17 – 21 Nanometers
Final collector
21 – 25 Nanometers
Spark plugs
20 – 28 Nanometers
Thermostat case
17 – 21 Nanometers
Bolts of a cover of a head of the block of cylinders (a tightening order – see in subsection 4.1.5.4)
  – bolts 1 – 6 and 9, 10
5 – 7 Nanometers
  – bolts 7 and 8
2 – 2,5 Nanometers