Ford Sierra

1982-1993 of release

Repair and operation of the car



Ford Siyerra
+ 1.2. Identification of the car
+ 2. Maintenance
+ 3. General data
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
- 8. Steering
   8.1. Technical characteristics
   8.2. Removal and installation of steering transfer
   8.3. Dismantling and assembly of steering transfer
   8.4. Removal and installation of a steering column
   8.5. Dismantling and assembly of a steering wheel
   - 8.6. Steering with the hydraulic booster
      8.6.1. Technical characteristics
      8.6.2. Removal and installation of steering transfer
      8.6.3. Removal and installation of the hydraulic pump
      8.6.4. Dismantling and assembly of steering transfer of CAM GEAR
      8.6.5. Dismantling and assembly of steering transfer of ZF
      8.6.6. Removal and installation of a steering column
      8.6.7. Dismantling and assembly of a steering wheel
      8.6.8. Removal of air from system of steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


a773976c



8.6.5. Dismantling and assembly of steering transfer of ZF

Dismantling

PERFORMANCE ORDER
1. To disconnect pipelines of giving and return of oil from the hydraulic amplifier. To muffle the ends of pipelines traffic jams for protection against pollution.
2. To disconnect tips with spherical hinges from steering drafts after weakening of fastening of lock-nuts.
3. To remove collars of fastening of casings and protective rubber a casing from the transfer case.
4. To move a gear lath from an emphasis against the stop for removal of the oil which remained in the hydraulic amplifier.
5. To move a gear lath to extreme situation and to clamp a lath (for teeths) in a vice.
6. To remove clamps of fastening of steering drafts and to disconnect steering drafts from the gear river.
7. To unscrew pusher cover bolts, to uncover, take adjusting laying, a spring and a pusher.
8. To unscrew the lower stopper from the case of a driving gear wheel of steering transfer.
9. To unscrew a lock-nut of a driving gear wheel of steering transfer.
10. To designate the provision of a driving gear wheel corresponding to advance and also a vystupaniye of a gear lath from both parties of the case.
11. To remove a casing of a driving gear wheel of steering transfer and a lock ring of the bearing.
12. To take a driving gear wheel of steering transfer from the case together with the bearing.
13. To remove flat laying, a sealant and the bearing from a shaft of a driving gear wheel.
14. To designate the provision of a casing of a gear lath and adjusting ring with a carving concerning the case of a driving gear wheel.
15. To unscrew an adjusting ring with a carving, to remove a casing of a gear lath, to take laying of round section and nylon remote laying.
16. To clamp the case of a driving gear wheel in a vice.
17. To take a gear lath and the remote plug.
18. To take, without having damaged a gear lath, a lock ring from the remote plug and to take laying, laying of round section and laying of the piston of the amplifier. To take other flat laying and a lock ring.
19. To take the remote plug.
20. To take a sealant of a gear lath and slanted remote laying from the remote plug.

Check of a gear lath

PERFORMANCE ORDER
1. To check a condition of the interacting surfaces:
      – a sealing ring with shaft of a driving gear wheel of steering transfer;
      – teeths of a gear lath and driving gear wheel, and also working surface of a pusher;
      – teflon sealant of the dividing valve of steering transfer.
2. To check and wash out hydraulic the pipeline and channels:
      – pipelines and the roundabout channel (by-pass) in the case of a gear lath;
      – dividing valve.
3. To replace the worn-out or damaged details and to grease edges of sealing rings with Calipsol lubricant.

Prevention

The teflon ring of the union of the dividing valve just before installation should be lowered in the boiling water in order that it could settle down correctly.

The driving gear wheel of steering transfer and the dividing valve are completed with couples and they need to be replaced together.


Assembly

PERFORMANCE ORDER
1. To install a new sealing ring in the case of a driving gear wheel.
2. To establish a gear lath in a vice.
3. To insert on a gear lath the remote plug with slanted laying and a sealing ring.
4. To establish laying of the piston with new laying of round section. To put on flat laying and lock rings.

Prevention

In the course of installation of lock rings it is necessary to preserve a gear lath against damage.


5. To install the nylon plug and laying of round section in the case of a driving gear wheel.
6. To enter 40 g of solid lubricant between teeths of a gear lath and to move it in the case against the stop of the remote plug to the gear wheel case.
7. To oil an adjusting ring of a casing with a carving. To establish a casing and the case of a driving gear wheel according to the designations executed in the course of transfer dismantling.
8. To tighten a ring with a carving by means of the corresponding key and to record from unscrewing by a kerneniye of the case of a driving gear wheel in places of undercutting of a ring.
9. To insert the lower bearing of a driving gear wheel and a lock ring.
10. To establish a gear lath on average situation and to insert a driving gear wheel according to the designations executed in the course of transfer dismantling.
11. To put on the top laying and a lock ring a shaft of a driving gear wheel.
12. To tighten a lock-nut of a driving gear wheel and to establish the casing filled with solid lubricant.
13. To establish a pusher, a spring, adjusting laying of a gap, and also the cover greased with the pressurizing paste.
14. To move a gear lath so that its teeths were visible. To clamp it in a vice, to fix steering drafts and to insert new clamps.
15. To establish rubber protective a casing and to record their new collars of fastening.
16. To screw on steering drafts tips with spherical hinges and to record them from unscrewing by lock-nuts.