Ford Sierra

1982-1993 of release

Repair and operation of the car



Ford Siyerra
+ 1.2. Identification of the car
+ 2. Maintenance
+ 3. General data
- 4. Engines
   - 4.1. Petrol engines
      + 4.1.1. Technical characteristics
      4.1.2. Adjustment of gaps of valves
      + 4.1.3. System of ignition
      + 4.1.4. Fuel system
      - 4.1.5. The repair which is not demanding removal of the engine
         4.1.5.1. Removal and installation of a gear belt
         4.1.5.2. Removal of a head of the block of cylinders
         4.1.5.3. Dismantling and assembly of a head of the block of cylinders
         4.1.5.4. Installation of a head of the block of cylinders
      4.1.6. Removal and installation of the engine
      4.1.7. Dismantling of the engine
      4.1.8. Identification of the interacting parts
      4.1.9. Assembly of the engine
      4.1.10. Replacement of pistons
      4.1.11. Removal and installation of an intermediate shaft
      4.1.12. System of gas distribution
      4.1.13. Lubrication system
      + 4.1.14. Cooling system
      4.1.15. Suspension bracket of the power unit
      4.1.16. System of production of the fulfilled gases
   + 4.2. Diesel engine
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


a773976c



4.1.5.1. Removal and installation of a gear belt

GENERAL INFORMATION

Bolts of fastening of a casing of a belt

Removal of the tension device of a gear belt by means of a key 21.012

1 – tension device,

2 – spring,

3 – adjusting bolt,

4 – roller of the tension device.

Adjusting signs of system of gas distribution

 

Removal

PERFORMANCE ORDER
1. To install the transmission in neutral situation and to fix the car the parking brake.
2. To take off maple a belt for what to weaken the bolts fixing the generator and to shift it towards the engine.
3. To install the piston of 1 cylinder in the top dead point, turning a bent shaft for a bolt, the fixing pulley of a maple belt, in the direction of working rotation until the tag of the top dead point is not combined with a tag on a casing.
4. To unscrew the bolts fixing a casing of a gear belt, to reject aside and forward and to remove it.
5. To weaken a tension of a gear belt, in the beginning having unscrewed a bolt with an internal hexagon (s=6 key) on the belt tension block, and then a bolt with a six-sided head (s=16) and overcoming spring resistance, to incline the block of a tension and полнлстью to turn off bolts.
6. To remove a belt pulley from a bent shaft. If the gear belt is removed only from a cam-shaft pulley, then it is not necessary to remove a pulley from a bent shaft.
7. To take off a gear belt.

Prevention

It is impossible to turn the engine for a cam-shaft pulley as it can destroy a belt. In the presence on a belt of cracks, traces of oil or porezhdeniye of teeths, the belt needs to be replaced.
that belt by means of a key 21.012.



Installation

PERFORMANCE ORDER
1. To check coincidence of tags on a pulley of a cam-shaft and a head of a bdok of cylinders. If necessary to combine tags.
2. To establish an intermediate shaft so that the tag on a rotor of the distributor was over a tag on the edge of the distributor. It is previously necessary to uncover the distributor having raised the screw-driver 2 side fixing brackets and having unscrewed 2 screws of fastening of a cover.
3. To establish a gear belt on a pulley of a bent shaft and to tighten on cranked to a shaft a pulley of a maple belt.
4. To establish a gear belt on a pulley of a cam-shaft and to weaken the belt tension block.
5. To turn on two turns a bent shaft for a pulley of a maple belt so that the block of a tension became on a gear belt and to tighten the tension block: at first a bolt with a six-sided head, and then with an internal hexagon.
6. To turn a bent shaft on 2 turns and to check compliance of tags on a pulley of a cam-shaft, a rotor of the distributor of ignition and a pulley of a maple belt of a bent shaft.
7. To establish a casing of a gear belt.
8. To establish an ignition distributor cover (see rice. Adjusting signs of system of gas distribution).