Ford Sierra

1982-1993 of release

Repair and operation of the car



Ford Siyerra
+ 1.2. Identification of the car
+ 2. Maintenance
+ 3. General data
- 4. Engines
   - 4.1. Petrol engines
      + 4.1.1. Technical characteristics
      4.1.2. Adjustment of gaps of valves
      - 4.1.3. System of ignition
         4.1.3.1. The sensor of impulses with Hall's converter
         4.1.3.2. To distribute ignitions
         4.1.3.3. Switchboard
         4.1.3.4. Remarks on operation
         4.1.3.5. Installation of a corner of an advancing of ignition
         4.1.3.6. Definition of malfunctions
         4.1.3.7. Removal and installation of the distributor of ignition
      + 4.1.4. Fuel system
      + 4.1.5. The repair which is not demanding removal of the engine
      4.1.6. Removal and installation of the engine
      4.1.7. Dismantling of the engine
      4.1.8. Identification of the interacting parts
      4.1.9. Assembly of the engine
      4.1.10. Replacement of pistons
      4.1.11. Removal and installation of an intermediate shaft
      4.1.12. System of gas distribution
      4.1.13. Lubrication system
      + 4.1.14. Cooling system
      4.1.15. Suspension bracket of the power unit
      4.1.16. System of production of the fulfilled gases
   + 4.2. Diesel engine
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


a773976c



4.1.3.7. Removal and installation of the distributor of ignition

GENERAL INFORMATION

System of ignition Lucas

1 – ignition coil,

2 – ignition switchboard,

3 – ignition distributor case,

4 – driving gear wheel,

5 – ignition distributor shaft,

6 – Hall's sensor,

7 – sensor rotor,

8 – distributor rotor,

9 – ignition distributor cover

Removal

PERFORMANCE ORDER
1. To disconnect the accumulator from car electric equipment.
2. To disconnect wires of high voltage from spark plugs and the distributor and to remove the distributor of high voltage.
3. To install the piston of the 1st cylinder in VMT. For this purpose it is necessary to rotate a hand a bent shaft of the engine to situation in which the rotor of the distributor will be established opposite to contact of the 1st cylinder in the distributor of high voltage of the distributor of ignition.
4. To designate this provision of a rotor of the distributor concerning the ignition distributor case for simplification of further installation of the distributor of ignition.
5. To unscrew a bolt of fastening of the case of the distributor of ignition and to remove the ignition distributor.

Installation

PERFORMANCE ORDER
1. To check whether there is a piston of the 1st cylinder in VMT (combination of the corresponding sign on a pulley with a constant sign (see rice. Control signs for installation of a corner of an advancing of ignition of ignition).
2. To insert the ignition distributor into an opening in the block of cylinders of the engine, to insert a bolt of fastening of the distributor of ignition, but not to tighten it.
3. To check combination of a sign on the distributor case with the provision of a rotor of the distributor corresponding to situation opposite to contact of the 1st cylinder of the distributor of high voltage.
4. To connect wires of high voltage to spark plugs and the distributor of high voltage.
5. To connect the accumulator to car electric equipment.
6. To establish an ignition advancing corner by means of a stroboscopic lamp (see subsection 4.1.3.5).