Ford Sierra

1982-1993 of release

Repair and operation of the car



Ford Siyerra
+ 1.2. Identification of the car
+ 2. Maintenance
+ 3. General data
+ 4. Engines
+ 5. Coupling
- 6. Transmissions
   + 6.1. Mechanical four-speed transmission
   + 6.2. Mechanical five-speed transmission
   - 6.3. Automatic Ford C 3 transmission
      6.3.1. Technical characteristics
      6.3.2. Service and repair
      6.3.3. Check of level of oil in the transmission
      6.3.4. Check and washing of hydrokinetic transfer
      6.3.5. Check of pressure of oil in operating time of the transmission
      6.3.6. Test of an overload of the engine hydrokinetic transfer
      6.3.7. Check in the course of the movement
      6.3.8. Adjustment of a tape of a brake of forward planetary transfer
      6.3.9. Removal and installation of the transmission
      6.3.10. Removal and installation of a cable of the kick-down mechanism
      6.3.11. Removal and installation of the relay of safe start of the engine
      6.3.12. Malfunctions and methods of their elimination
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


a773976c



6.3.9. Removal and installation of the transmission

Removal

PERFORMANCE ORDER
1. To install the car over the viewing channel or on the elevator and to disconnect a weight wire from the accumulator.
2. From a motor compartment to unscrew four top bolts of fastening of the automatic transmission to the block of cylinders of the engine.
3. To unscrew brackets of the vacuum pipeline, and also the pipeline of filling of transfer by oil.
4. To disconnect rubber elements of a suspension bracket from brackets of fastening of a back part of final system and to suspend system to a body by means of a wire.
5. To disconnect the driveshaft from the transmission and to muffle an opening in its back part of a case a stopper from artificial material in order that there was no oil effluence.
6. To remove the stabilizer.
7. To disconnect an oil pipeline from a radiator of oil and to muffle their openings.
8. To disconnect electric wires from a starter and to remove a starter.
9. To remove two protection and knot of drafts of the lever of gear shifting.
10. To disconnect a cable from the lever of a reduction of transfers and from the holder of a cable.
11. To disconnect a linking of electric wires from the relay of safe start of the engine.
12. To disconnect a speedometer drive cable.
13. To disconnect the vacuum pipeline from the vacuum regulator of the automatic transmission.
14. To unscrew bolts of fastening of a disk of the drive of hydrokinetic transfer through an opening of the removed starter.
15. To unscrew bolts of fastening of a cross-piece from the transmission and to carefully lower the transmission.
16. To take the transmission, holding hydrokinetic transfer in its case.

Installation

PERFORMANCE ORDER
1. In case of need to take the rings directing a flange of hydrokinetic transfer and to press them into the block of cylinders of the engine.
2. To establish hydrokinetic transfer in a case if it was taken from it. The stopper of discharge of oil of hydrokinetic transfer has to be in an axis of an opening of a driving disk. After installation of hydrokinetic transfer on the appropriate place in a case it is necessary to check whether makes the control size (And, see rice. The control amount of deepening of hydrokinetic transfer) between a flange of hydrokinetic transfer and a frontal surface of a case of 10 mm.
3. To tighten flange bolts after check whether hydrokinetic transfer in a case freely rotates.
4. To oil for automatic transmissions and to insert the filling pipeline oil into the short pipeline on a case.
5. To attach a suspension bracket cross-piece to the transmission.
6. To lift the transmission and to fix a suspension bracket cross-piece to a body.
7. To insert and tighten the corresponding moment bolts of fastening of a driving disk to hydrokinetic transfer.
8. To connect electric wires to a starter and the relay of safe start of the engine, and also the vacuum pipeline to the vacuum regulator of the transmission.
9. To connect the pipeline to a radiator of oil and a speedometer drive cable.
10. To connect a cable to the holder about the transmission, and also to the lever of a reduction of transfers.
11. To install the lever of gear shifting and a control lever at the transmission in situation "D" and to fix elements of the external mechanism of management of the automatic transmission (without their drive).
12. From an opening in a back part of a case of the transmission to take a stopper from artificial material and to install the driveshaft.
13. To install the stabilizer of a forward suspension bracket.
14. To attach the brackets holding vacuum the pipeline and an oil pipeline.
15. To attach a suspension bracket of a back part of final system to a body.
16. To check the level of oil and if necessary to fill amount of oil in the transmission (see subsection 6.3.3).
17. To check tightness of connections and pipelines.