Ford Sierra

1982-1993 of release

Repair and operation of the car



Ford Siyerra
+ 1.2. Identification of the car
+ 2. Maintenance
+ 3. General data
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
- 9. Suspension brackets
   + 9.1. Forward suspension bracket
   - 9.2. Back suspension bracket
      9.2.1. Technical characteristics
      9.2.2. Replacement of the shock-absorber
      9.2.3. Replacement of a spring of a suspension bracket
      9.2.4. Removal and installation of the lever of a suspension bracket
      9.2.5. Replacement of the metal-rubber plug of a beam of a suspension bracket
      9.2.6. Replacement of hug bearings of a back wheel
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


a773976c



9.2.3. Replacement of a spring of a suspension bracket

GENERAL INFORMATION

Removal of a spring of a back suspension bracket

1 – brackets of fastening of brake hoses,

2 – lower fastening of the shock-absorber,

3 – fastening of a beam of a back axis to a body,

4 – axis of rotation of the lever

Removal

PERFORMANCE ORDER
1. To take off a protective cap of a back wheel and to weaken nuts of fastening of a wheel.
2. To lift and record a back part of the car, to remove the corresponding back wheel.
3. To remove the brake drum (see subsection 10.3).
4. A cap key to unscrew four bolts of fastening of the case (5, see rice. Back suspension bracket) of wheel bearings, rotating a nave of a back wheel so that its openings settled down on continuation of an axis of separate bolts of fastening of the case of hug bearings.
5. To remove from within the bearing brake disk a plastic casing of the external driving hinge of a half shaft after a raising the screw-driver of tightening rings on heads of bolts and unscrewing of bolts of fastening of a casing.
6. To take a half shaft entirely through the bearing board of a back brake, directing it directly and holding so that it did not overhang down.
7. To take an U-shaped clamp and to remove a brake hose (without disconnecting it) from the holder under the bottom about a wheel.
8. To establish a jack under the lever of a suspension bracket and to lift the lever so that all loading fell on a suspension bracket spring.
9. To unscrew the lower fastening of the shock-absorber (a body of Berlin) or to remove the shock-absorber (a komba body).
10. To unscrew from the relevant party bolts of fastening of a beam of a back axis to a body after bending back of safety laying and unscrewing of a bolt of fastening of the metal-rubber plug (8, see rice. Back suspension bracket), and also two bolts of fastening of this plug to a body.
11. To carefully lower the lever down.
12. To take a suspension bracket spring together with a rubber basic cup.

Installation

PERFORMANCE ORDER
1. To establish a spring together with a rubber basic cup on a suspension bracket lever shoulder.
2. To lift a jack to put a spring on the appropriate place.

Prevention

With a komba body along with a spring it is necessary to install the shock-absorber in cars.


3. To attach the metal-rubber plug of a beam of a back axis to a body, having tightened bolts of its fastening the corresponding moments.
4. To install the lower fastening of the shock-absorber (in cars with a komba body), and also connection of a brake hose on the holder of a body and to record it.
5. To take a jack.
6. To establish a half shaft with a wheel nave. To attach a wheel nave four new bolts to the suspension bracket lever, tightening them the corresponding moment.
7. To establish a plastic casing of the external driving hinge of a half shaft from within the bearing brake board.
8. To install the brake drum.
9. To establish a wheel, to put the clamps of fastening of a wheel, to lower the car and to tighten nuts of fastening of a wheel the corresponding moment.