Ford Sierra

1982-1993 of release

Repair and operation of the car



Ford Siyerra
+ 1.2. Identification of the car
+ 2. Maintenance
+ 3. General data
+ 4. Engines
+ 5. Coupling
+ 6. Transmissions
+ 7. Driveshaft and back bridge
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
- 12. Electric equipment
   12.1. Technical characteristics
   12.2. Relay and safety locks
   12.3. Removal and installation of the generator
   12.4. Dismantling and assembly of the generator
   12.5. Adjustment of a tension of a maple belt
   12.6. Starter
   12.7. Windshield screen wiper, knot of indexes and headlight
   12.8. Removal and installation of a combination of devices
   12.9. Adjustment of light of headlights
   + 12:10. System of heating and ventilation
   + 12:11. Electrical circuitries


a773976c



12.7. Windshield screen wiper, knot of indexes and headlight

GENERAL INFORMATION

Windshield screen wiper

 

1 – engine,
2 – holder,
3 – drafts,
4 – axes of levers of screen wipers,
5 – screen wiper lever,
6 – brush

Removal of the engine of a screen wiper

PERFORMANCE ORDER
1. To include a screen wiper and at the time of emergence of a nut of fastening of a crank on a shaft of the engine to switch off ignition or to remove a weight wire from the accumulator plug.
2. To unscrew a nut of fastening of a crank (2) on a shaft of the engine and to remove it. To unscrew three bolts (1) of fastening of the engine of a screen wiper to an arm.
3. To take the engine of a screen wiper and to disconnect the socket of electric wires.

Installation of the engine of a screen wiper

PERFORMANCE ORDER
1. To connect the socket of electric wires to the screen wiper engine.
2. To insert the engine of a screen wiper and to tighten bolts of fastening of the engine of a screen wiper to an arm.
3. To establish a crank of the lever mechanism on an axis of the engine and to check whether the crank ledge entered deepening of an axis of the engine.
4. To tighten a nut of fastening of a crank to an engine axis.
5. To connect a weight wire to the accumulator (if it was removed) or to include ignition and to check correctness of functioning of a screen wiper of a windshield.

Removal and installation of the lever mechanism of a screen wiper

PERFORMANCE ORDER
1. To disconnect a weight wire from the accumulator
2. To reject up a plastic protective cap of the lever of a screen wiper, to unscrew a fastening nut, to remove a washer and the lever of a screen wiper together with a brush (see rice. Windshield screen wiper).
3. To repeat the described actions for the second lever of a screen wiper.
4. To lift a cowl, to disconnect pipelines of supply of liquid to nozzles of a washer of a windshield and to unscrew on one bolt on both ends of a lattice of air supply in a body.
5. To close a cowl and to unscrew eight bolts after removal of plastic casings.
6. To remove an air supply lattice in a body.
7. To unscrew seven bolts of fastening of the holder of the lever mechanism of a screen wiper of a windshield (shooters showed the provision of seven bolts of fastening).
8. To take the holder together with the engine of a screen wiper and the lever mechanism.
9. To disconnect electric wires from the engine.

Prevention

Drafts of the mechanism are connected to its cranks by means of spherical nylon fingers. Fingers should be taken carefully by means of the lever, and to insert after a covering graphite lubricant.


10. For installation of the lever mechanism it is necessary to perform operations in the return sequence in relation to removal process.